MKE
wurde zum Anschluss von Tastaturen der Firma Fatar entwickelt. Falls Sie
eine andere Tastatur an die MKE-Elektronik anschließen wollen, so
beachten Sie bitte die folgenden Hinweise:
-
Zur
Auswertung der Anschlagdynamik muss jede Taste mit zwei
Einschaltkontakten ausgestattet sein, die nacheinander schalten.
Umschaltkontakte, wie sie früher für anschlagdynamische Tastaturen
verwendet wurden, sind nicht geeignet !
-
Die
Tastenkontakte müssen in Form einer Dioden-Matrix verschaltet werden.
Die Schaltbilder für die 4 möglichen Versionen der Dioden-Matrix
können Sie in Form von gif-Dateien von unserer Web Site
herunterladen:
-
Die
zuerst schaltenden Kontakte sind in den Schaltbildern mit BR...
(break) bezeichnet, die danach schaltenden Kontakte mit MK... (make).
-
Für
die Verbindung zwischen MKE und Tastatur werden
Micromatch-Steckverbinder der Fa. AMP verwendet, da diese kompatibel
zu den Steckverbindern der Fatar-Tastaturen sind. Sowohl auf MKE wie
auch auf den FATAR-Tasturen befinden sich die weiblichen
Steckverbinder (Buchsen): 20-polig für die 2- und
3-Oktaven-Tastaturen, 2 x 16-polig für die 4- und
5-Oktaven-Tastaturen. Die Verbindung zwischen MKE und Tastatur wird
mit 16- bzw. 20-poligen Flachbandkabeln hergestellt, die an beiden
Enden mit den passenden männlichen Gegenstücken (Stiftleisten in
Einpresstechnik) versehen sind.
-
Falls
Sie MKE ohne Tastatur bestellen, geben Sie bitte an, welche Art von
Steckverbindern bestückt werden sollen, da diese für die
verschiedenen Tastatur-Versionen unterschiedlich sind (siehe
obenstehende Schaltbilder).
-
Sie
können MKE auf Wunsch auch ohne bestückte Steckverbinder beziehen.
Sie können dann die Verdrahtung zwischen MKE und Ihrer Tastatur
selbst vornehmen.
-
Wir
bieten Steckverbindungssätze für die 4 verschiedenen Tastaturen an.
Diese bestehen aus einem oder zwei Flachbandkabeln mit den passenden
Gegenstücken zu MKE bzw. den Fatar-Tastaturen an beiden Enden. Preise
finden Sie in unserer Preisliste im
Bereich Ersatzteile ganz am Ende.
|
MKE
was developed for the connection to standard manuals of the Italian
keyboard manufacturer FATAR. If you want to connect MKE to another manual
or if you want to use your own manual and contacts please pay attention to
the following remarks:
-
Each
key has to be equipped with two contacts that switch "on"
one after another. The time between the first and second contact is
used to calculate the Midi velocity. Change-over contacts as used in
earlier velocity-sensitive manuals cannot be used !
-
The
contacts have to be wired as diode matrix. The schematics
for the keyboard contact boards are available as
gif files (they show the double contacts for each keym the diode matrix
and the connectors):
-
The
contacts switching at first are labelled BR... (derived from break),
the second contacts are labelled MK... (derived from make).
-
In
the MKE the same type of connectors as in the FATAR manuals are used (Micromatch
connectors made by AMP). The MKE uses female micromatch connectors (20
pins for the 2 and 3 octaves version, 2 x 16 pins for the 4 and 5
octave versions). The same type of connectors are available at the
FATAR manuals. The connection between MKE and the FATAR manuals is
made with 16 resp. 20 pin ribbon cables equipped with the
corresponding male connectors on each side.
-
If
you order MKE without manual please specify which type of connector
you want to have at the MKE (20 pin for 2 resp. 3 octaves or 2 x 16
pin for 4 resp. 5 octaves).
-
The
MKE is available even without the AMP micromatch connectors. In this
case the corresponding pins on the MKE pc board are unused and you
could solder the wires, that lead to your manual resp. contacts,
directly to the pins without usage of the AMP connectors..
-
We
offer cable sets for the 4 different manuals. They are made of one 20
pin or two 16 pin ribbon cables with the suitable male connectors on
each side. They fit exactly to MKE and the FATAR manuals.
The
prices for the cables can be found in the price
list in the spare parts section.
|